Results 1 to 18 of 18

Thread: Nautitech 441/442 Onwers?

  1. #1

    Default Nautitech 441/442 Onwers?

    Hello Everyone. Any Nautitech 441/442 owners on this site? We are looking for feedback on the good/bad/ugly in regards to a 9-year old x-charter Nautitech Cat.

    Thanks!

  2. #2
    Join Date
    Nov 2018
    Location
    St RaphaŽl, France
    Posts
    2

    Default Re: Nautitech 441/442 Onwers?

    Hello,
    I just bought Powathan, a 6 yr old Nautitech 442, 4 cabins version. At first glance, good quality of build, easy access to most of electric, water, electronic circuits, nice interior layout but lockers in cabins are few and narrow, there is more free space under beds. I just had a short trial at sea under sails, good performance downwind, fair upwind. The engine bilges are very deep and engine access is not easy, despite of an opening in transoms to reach the rear part of the engines. Sails trim is very simple, short rail for main and no rail, only 2 blocks, for genoa sheets. All halyards and reefing lines are on mast foot, you cannot act on them from the cockpit.
    I''l be able to say more in the next few weeks.

  3. #3

    Default Re: Nautitech 441/442 Onwers?

    Thanks Powhatan. I'm glad you are enjoying the 'new' boat! I guess it will be a very Merry Christmas for you!!

    Please keep us updated on your observations and thoughts about modifications.

    Cheers!

  4. #4

    Default Re: Nautitech 441/442 Onwers?

    I was also wondering why this vessel is listed with a 44-ft LOA and a 40-ft LWL? With its near vertical bows, where does the 4 feet go? Is this a misprint that all the reviews keep carrying over? Or did someone include the bowsprit in the LOA?

  5. #5
    Join Date
    Nov 2018
    Location
    St RaphaŽl, France
    Posts
    2

    Default Re: Nautitech 441/442 Onwers?

    The bowsprit is a possible explanation. On my registration papers the LOA is 13,4 m, which is exactly 44 ft, but the LWL is not described. In some ports it can happen that they measure the LOA with laser devices to calculate mooring fees, and it always includes bowsprit, dinghy, and anything exceeding the outer limits of the boat.

  6. #6
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    Looking at the Nautitech 40.2 and 441,442. I found that I can’t fit in the bunks on the 40.2 4 cabin, but the owners bunk is long enough for me. The extra few inches in length for the 441,442 bunks makes them adequate. If I buy one of these I would have to add waste tanks to bring them into US waters And need to account for the cost to convert it. No problem with the 220Vac wiring. I think an isolation transformer with dual input taps for 120 or 220 is advisable for shorepower on any boat. I saw Nautitech’s holding tank above the head solution and can tell you from 20 yrs experience with this that you don’t want to rely on a jocker valve to keep your holding tank from deposting it’s content on your floor. Any proper solution puts the tank below the head. Less head pressure (pun intended) that way.

  7. #7

    Default Re: Nautitech 441/442 Onwers?

    Thanks for the feedback Capt. Rehab. As a big guy; a big bed and a big head are necessary. I saw the overhead tanks and was already planning to combine at least one of the double heads into a single (larger) unit. After 11 years, we are fans of the Lagoon setup on our older model (very robust and error-free). I think we would emulate that design if we move forward on a 441... But I'm still wondering just how much bigger a 441/442 is compared to our Lagoon 38? I mean we walked by a bunch of them 2 years ago in Le Marin Martinique - and of course I never asked the charter companies if we could step about to check them out (so much for forward vision).

  8. #8
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    Not sure about the comparison to the Lagoon 380 but I don’t recall the berths being cramped when I chartered one for a week. The 441/442 are pretty tight at 6’5” but not uncomfortable. Also I prefer the single helm. Nautitech did the dual helm right on the Bavaria Open 40. I really loved those dual helms. The 40.2 dual helms were awful. The stanchions were always loose as if they spent much of the time trying to keep the helmsman from going overboard. Much better protection on the open 40. Also easy to walk between the two helms on the open 40 and not so easy on the 40.2. The moving seat on the 40.2 makes a mess of the path to the stern as well.
    Last edited by Capt.Rehab; 17th December 2018 at 05:11 PM.

  9. #9
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    The Open 40 helm

  10. #10
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    Quote Originally Posted by Capt.Rehab View Post
    The Open 40 helm
    Attached Images Attached Images

  11. #11
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?



    The 40.2 helm, more exposed rhan on the Open 40
    Attached Images Attached Images
    Last edited by Capt.Rehab; 18th December 2018 at 12:34 PM.

  12. #12
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?



    Another style 40.2 helm

  13. #13
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?



    Catana 42 helm. Similar to 40.2

  14. #14
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?



    The 441 helm.
    Attached Images Attached Images

  15. #15
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    In general the narrow hulls on all the Nautitech boats had less room in the berths and heads than Lagoon or Fountaine Pajot of similar length

  16. #16

    Default Re: Nautitech 441/442 Onwers?

    Yep, thanks. We've seen the differences.

    Any comment on longevity issues? Hull or deck concerns? Or any legacy weaknesses in general? Thanks!

  17. #17
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    Quote Originally Posted by Coatal Ogre View Post
    Yep, thanks. We've seen the differences.

    Any comment on longevity issues? Hull or deck concerns? Or any legacy weaknesses in general? Thanks!
    Nothing obvious when looking at any of the boats other than the wear and tear you might expect on a used charter boat. Every boat I looked at had some water damage to interior wood. Most likely the ports were left open in the rain and nobody wiped up the water so the finish on the wood suffered. At least the maintenance people made an attempt to make some repairs.

    I have only toured one catamaran factory and that was Catana. The workmanship and engineering that goes into the new 53 is quite impressive.
    As far as Hull/Deck concerns I would choose PVC foam over balsa as a core material. End grain balsa probably has better sheer strength, but it will rot when wet

  18. #18
    Join Date
    Dec 2018
    Location
    New England
    Posts
    11

    Default Re: Nautitech 441/442 Onwers?

    Typo Should be shear strength. It also has substantially greater compressive strength than the PVC core. Still any damage to the skin would expose the core to water and that is why I prefer the PVC foam. You do have to adjust the lamination to compensate for the difference

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •